Using a linear potentiometer

As one of a number of alternatives to the AS5040/AS5045, the shackunit accommodates use of a potentiometer at the antenna. This offers accuracy within a few degrees, depending on its linearity/quality. The actual Analogue/Digital conversion in the shack unit is able to decode one part in 1024 but most potentiometers are not this accurate. Simply connect a linear potentiometer to the DB9 (pins 4 and 5 with the wiper to pin 8) and set the menu item of the shack unit to 10 bit for the appropriate port (menu items 25,26). Rotators vary in the wiring of the potentiometer. Some are wired as a true potentiometer with floating wiper, others such as my CDE44 (and the Ham M and family) are wired as potentiometers but with the wiper earthed. If it is possible to replace the pot you will get better performance by using a hall effect solution such as those described elsewhere in this website. However for those with broad antennas or existing rotators the existing pots/rheostats are a workable solution for satellite use.

If your rotator has its indicator wired as a rheostat you can make this work quite well by providing a constant current souce. An LM317 wired as a constant current source uses just the chip plus a resistor, see the LM317 datasheet for an example. You need to choose the value of the series resistor to provide a constant current of 5V/Rohms. For example if you have a 500 ohm rheostat in the rotator housing then you need a constant current of 5/500=10mA. Fine tune the value of the series resistor so that at maximum resistance on the rheostat the voltage is 5V. To protect the A/D converter on the PIC you might want to put a 5.1V zener on the output of the constant current source to protect against the voltage going beyond 5.5 volts - the maximum allowable on the PIC.

I found that putting a 10uF from the wiper to the earth connection seems to smooth things out a bit and it helps a lot to set averaging on too (that's menu item 27 in Ver 7.02 and 28 in Ver 8.00). A potentiometer from 500 ohms to 4K7 linear would work satisfactorily. Too high a value may result in increased error as the load impedance of the A/D input to the 18F4620 becomes significant.

The AZ/EL board is not required for potentiometer use.

An AS5040, an AS5045, or an MA2/3 series from US-digital can all be used to generate a DC voltage either by integrating the PWM output (MA2/3-P) or by choosing a device that outputs a DC voltage (MA2-A).

My satellite system - Murphy at work

My most recent project has been to get my satellite system working. I have used my old CDE44 rotator - the small brother of the Ham M and similar rotators for azimuth rotation. Like the Ham M it has a large wire wound potentiometer at the top of the rotator actuated by a molded slot in the dome section.

I experienced a very frustrating time when I hooked the pot to my beam rotator system and suddenly the voltage on the wiper disappeared. At that point I examined the circuit of the CDE44 more closely and I had overlooked that the wiper of the pot is earthed. Floating the power supply of the 'shack unit' partially sorted the problem but it was unreliable and there was severe jitter of the readings when the rotator motor was turning. Some work with a CRO showed that there was almost 1/2 volt of AC superimposed on the DC voltage coming back from the pot caused by an earth loop within the system. The solution was to modify the rotator and isolate the pot wiper from earth..

There are two earthing points for the wiper of the pot. One is under the pot and consists of a flexible piece of metal held by a circlip and attached to the body of the rotator by the pot attachment bolt. It is easily seen when the pot is unbolted from the body. Two nuts with star washers hold the pot on.

Under the pot showing the earth strap in its original position

A simple modification is to rotate the flexible piece of metal about a quarter of a turn and drill a hole to fasten it to the plasticof the pot body with a new bolt/tag/washer/nut. I used a Dremel milling bit to remove a small amount of the plastic from the top side of the pot body to ensure a bolt head (3mm or 1/8 in) would sit flat. A wire is run from this now insulated point under the pot to terminal 2 on the connection strip at the bottom of the rotator. In a CDE44 there is no brake solenoid and this terminal is unused. If you use this mod on a Ham M or similar you will need to find another way of terminating the new wiper connection as terminal 2 is used for the brake solenoid.

Next, you have to overcome the accidental earthing of the wiper through the driving mechanism of the wiper. The original design has an upturned lip with slots that fit into the dome when the unit is assembled.

Original top of the pot showing the drive mechanism. The lip is
just visible on the left above the wiper.

For this part of the modification I found it easier to remove the wiper mechanism from the pot by removing the circlip (be careful - don't let the circlip shoot off, never to be found again). Next cut the lip from the drive piece (tin snips work OK) and then construct a plastic replacement for the drive lip. I used a hard teflon like plastic that cut nicely and I was able to make an 'L' shape that could be bolted to the wiper drive assembly. See photo. I used careful measurement and use of a hacksaw blade to create the slots forming a better than original drive mechanism. I tested that the piece of plastic located nicely in the dome slot before fastening it with three 2mm bolts/nuts to the drive metal sheet.

The new plastic drive system at right. At left can be seen
the added brass bolt holding the earth strip to the plastic body.

It all went very smoothly and the system now works really well. Because the system is used for satellite work I did not need the ultimate accuracy so hysterisis of the azimuth section of the beam rotator unit is set to 3 degrees. In my case that stops hunting.

last update 20 May 2009